美国MERCOTAC水银滑环，M630，630-SS， Slip Ring

630型无刷滑环

导体:六导体

安培:2@4安培，4@30安培

伏:250

Mercotac®630型无刷滑环确保在固定和旋转组件之间可靠地传输电力，控制信号和数据。这些滑环专为机械臂、半导体设备、转盘、风力涡轮机和机器人等各种应用而设计，即使在具有挑战性的环境中也能确保安全可靠的运行。高度通用和可靠，它们对于需要强大的电气旋转连接的行业至关重要。

优点:

耐用，紧凑，低成本

用于信号和/或电源连接

易于安装和更换

IP 51防护等级与启动套件

重量轻，坚固的金属结构

耐用、节能、免维护

美国制造

Model 630 Product Specifications

Dimensions

• Details:

• Disconnects are included

• 55252 Large Straight Disconnect (Qty. 4)

• 55251 Large Flag Disconnect (Qty. 4)

• 55253 Shrink Tube (Qty. 4)

• 55110 Small Straight Disconnect (Qty. 4)

• Available with stainless steel ball bearing (630-SS) (recommended for wet or corrosive environments)

• Dust/Splash Boot Kit available.

细节:

包括断开连接

55252大直通断开(数量4)

55251大标志断开(数量4)

55253收缩管(数量4个)

55110小型直接断开(数量4)

可配置不锈钢球轴承(630-SS)(建议用于潮湿或腐蚀性环境)

灰尘/飞溅启动套件可用。

Description: Boot Kit Parts
Item #: 57630

• Vinyl Boot Kit for dust and splash protection

• IP51 protection rating

Description: Boot Kit Shown Assembled
Item #: 57630

• Vinyl Boot Kit for dust and splash protection

• IP51 protection rating

Description: Large Flag Disconnect, Insulated
Item #: 55251

• 16 AWG - 14 AWG

• Qty. 4 included

• Maximum recommended Amps: 15

Description: Large Straight Disconnect, Non-Insulated
Item #: 55252

• Maximum recommended Amps: 15

• 16 AWG - 14 AWG

• Qty. 4 included

Description: Small Straight Disconnect, Insulated
Item #: 55110

• 22 AWG - 18 AWG

• Qty. 4 included

• Maximum recommended Amps: 4

Description: Shrink Tube
Item #: 55253

• Qty. 4 included

Description: Other Disconnects

• Disconnects for other wire gauges are available and can be substituted for the standard disconnects(22-18 AWG and 12-10 AWG). See Ampacity Table

Model 630 is typically mounted by either the black body or the white plastic bushing on either end using a set screw or split clamp. When used horizontally, mount the Mercotac so the body of the connector rotates.

Body Mount

Bushing Mount

Horizonal Mount to Body

Good mounting method
(but vertical orientation is better)

Adaptor Mount to Body

Use when the shaft diameter is smaller
than the body of the Mercotac.

Horizonal Mount to Bushing

Used if the shaft
cannot be fitted to the body diameter.

Thermal Insulated Mount to Bushing

May be needed if thermal insulation is necessary.
Used if the shaft cannot be fitted to the body diameter.

Top Mount to Body

Best mounting method.

Bottom Mount to Bushing

Floating Torque Arm Mount to Body

Protective Housing Mount to Body

Recommended for wash-down or dirty environments.
Also recommended for food processing .

Vibration Isolation Mount to Body

With flexible bellows.

Vibration Isolating Mount to Body

With floating drive coupling.

Installation Notes:

• The up arrow should not point below horizontal.

• Do not solder to or bend terminals.

• Avoid lateral forces and mechanical loads (overly stiff or tight wires).

• Do not rigid mount both ends of the Mercotac.

• Limit the mounting eccentricity (runout / wobble) to .005" (.13mm).

• Provide overload protection within the circuit.

• Avoid vibration and bumping motions.

Model 630 Standard Wire Connections

1. Wire connections, mounted inside rotating shaft.

2. Stationary end showing standard wire connections. The flag disconnects must be installed with the wires going counterclockwise as shown.

3. Wires crimp to terminals.
(Suggested tool: Thomas & Betts #WT 112M)

Model 630 Wire Connections with Optional Boot Kit

Wire connections, mounted inside rotating shaft.

Stationary end showing optional boot kit.

Cutaway view.